 |
| Quantity: | |
|---|---|
Hybrid RAL7035 Epoxy Polyester Powder Coating Paint for Aluminum Substrate
This series is a thermoset powder coating based on saturated polyester resins specially selected for exterior use. It is formulated to give properties of good flow-out and satin or glossy finish. Its outstanding resistance to ultra-violet light and atmospheric aging make it highly decorative and durable in outdoor environment,It is widely used for outdoor furniture,architectural hardware,air-conditioners,bicycle frames,garage doors and signboards etc .
GENERAL TYPES
Epoxy Polyester /Hybrid powder coating
Epoxy Powder Coating
Polyester TGIC -Free powder coating
Polyester TGIC Powder coating
Polyurethane powder coating
FUNCTIONAL TYPES
Anti-gassing Powder Coating for cast steel
Clear Topcoat Powder Coating
Heat Transfer Powder Coating
High Temperature Resistant Powder Coating
Metallic/Peal Powder Coating
Zinc Rich Epoxy Primer Powder Coating
Textures include sand grain, hammer, silk pattern, sand textured, marble,metallic, multi-color.
PHYSICAL PROPERTIES
Specific gravity : 1.2 ~ 1.8g/cm3 up to colors
Particle size distribution: 100% less than 100 microns (depending on the specific indicators art effects may be, according to the special requirements of painting adjusted)
Level of liquidity: 24 ~ 27 mm
CURING CONDITIONS
180 °C ~ 200 °C (work piece temperature), 10-15 minutes
AVERAGE COVERAGE
8-12 square meters / kg, thickness 60 microns (100% of the powder coating utilization rate)
PACKING
Outside carton lined with two layers of polyethylene bags, each containing 20 kg net weight.
STORAGE AND TRANSPORT
Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure. Storage products in line with the above conditions, since the date of production, effective storage period is 6 months. Over the storage period may be re-tested and the results were consistent with, can still be used.
HEALTH AND SAFETY for powder paint for metal structure
Powder coating is a non-toxic products, but should be avoided in the course of inhalation of dust. Proposed operators wear appropriate dust mask, glasses. If possible, try to avoid long-term skin contact with powder coating
.
Mechanical property | ||
Testing items | Standards and methods | Inspecting index |
impact strength | GB/T1732-1993, AS3715 2.8 | 30-50kg/cm |
Bending resistance | GB/T1185-88, AS1580 402.1, ISO9227 | Pass 2-5 millimeters |
Adhesion CHECKED TEST | GB/T9286-88,2mm Cross cut, ISO2409 | Pass100/100, passes 0 levels |
Cupdrawing:Erichsen, ISO1520 | Erichsen, ISO1520 | Pass 3-7 millimeters |
Pencil hardness | GB/T6739-86, Mitsubishi | Pass H-2H |
Chemical resistance and weather resistance | ||
Salt spray test | GB/T1771-91,500 hours | The cross section of corrosion less than 2MM |
Hot and damp resistance test | the GB/T17740-79(89),1000 hours | Without air bubbles, loses the light slightly |
Acid resistance | 10% CH3COOH, 240 hours | Without air bubbles, the surface without damage |
Alkali resistance | 10% NaOH, 240 hours | Without air bubbles, the surface without damage |
Heat resistance | 200degree,1 hour | The color change is lower than E=1.5 |
Solvent resistance | MEK24 hours soaked in solvent-free | Without air bubbles, the surface without damage |
uvioresistant | QUV-313,500 hours | Gloss higher than 80% lower than the Munsell color change level |
Water tolerance of | 2 hours | No bubble, not falling, losing light |
More information about powder coating powder paint for metal structure,please visit www.fhpowdercoating.com
